304 Stainless Steel Speed Gate Swing Barrier Turnstile 120W Access Mechanism
304 Stainless Steel High Speed Gate Swing Barrier Turnstile Face Recognition Turnstile 120W Access Gate Mechanism
DC Brushless Motor Barrier Swing Gate Automatic Pedestrian Swing Barrier Turnstile With Face Reader
Glass Tursntile Pre-installation Alignment:
• Before anchoring the cabinets to the floor, we recommend laying out the lane and testing alignment.
•Place the cabinets in their approximate end location and connect the 2 conductor cable inside of the
primary cabinet to the end in the secondary cabinet. Plug in the primary cabinet to AC voltage to power
up the lane.
• Inside of the primary cabinet, there is a series of 7 total photo cell sensors. Each of these sensors is
equipped with two LED’s on the rear. One of them is green and should always be lit. The other should be
solid orange while the beam is uncrossed and off while the beam is crossed.
• If the orange LED is blinking in any case, you will need to adjust the sensor alignment, shift the cabinets
so that they are straight to each other, or shim the cabinets so that they are level.
Swing gate is the barrier gate blocking and releasing by swinging of the arm barrier. The material of the barrier
is usually stainless steel and acrylic. It is mainly used for the management of entries and exits.
The usual application places only allow people to pass, or for people who tow luggage, and disabled people.
Swing gate is an intelligent channel administration device that has been carefully developed, developed and
produced over the years. It is a high-tech product primarily for intelligent administration of personnel channels.
The gadget combines mechanical, digital, microprocessor control and numerous identification applied sciences,
and is equipped with quite a lot of identification system devices and reliable efficiency safety units, alarms, direction
indicators, and extended friendliness. The LED counting display interface coordinates the clever control and
management of the channel.
Swing gate has standard enter and output interfaces, and is the best choice for system integrators. It may be simply
compatible with IC card, ID card, barcode card, fingerprint and other card reader identification units, offering civilized
and orderly access for entry and exit personnel. Methods to successfully handle personnel out and in.
Main function and features
1. The stylish stainless steel column and clear toughened glass wing present a bright and concise design.
2. Bi-directional opening facilitates fast and safe access. It can also be integrated with recognition systems
for user friendly access control.
3. Featured with high security and stability, it’s suitable for banks, corporate headquarters, airports and leisure
4. Fault detection and alarm functions, easy to use and maintenance.
5. The running status can be programmed and controlled with the built-in keyboard on the main board.
6. Mechanical anti-pinch function. If the gate meets resistance in the reset process, motors will stop working
automatically within the prescribed time and reset again after the default delay (till fully reset).
7.Anti-breakthrough function. The gate is locked automatically until opening signal received.
8. Synchronization functions (for dual gate equipment).
9.Automatic reset function. Should the user fail to pass within the prescribed time (default time is 5 seconds),
the system will cancel the authority of the current user automatically.
10. Gate can be set as normally open or normally closed.
11. Can be used with variety of card readers: IC / ID card readers, bar codes, fingerprints, etc. (Via dry contact signal)
12. Direction can be set as unidirectional or bidirectional.
13. The device can be connected to management computer to realize remote control and management.
14. LED direction indicator (optional)
15. Gate auto opens when power off and auto close when power on, complying with fire safety requirements.
16. Support infrared photocell for anti-pinch and reset function.
||304# Stainless Steel (default), 201# or 316# Stainless Steel or paint (optional)
|Thickness of ply
||brushed surface, polishing surface
|Shell's size (L*W*H)
|Swing arm material
||Tempered glass or Acrylic (optional)
|Stretching out swing length
|The inductive card reader dimension
||equipped with the standard mounting brackets or tailor.
||Germany technological motor
||DC36 servo motor
|Passing speed in normally open mode
|Passing speed in normally closed mode
|Swing arm transmission angle
||unidirectional or bi-directional
|Opening / closing time
|The time required to running state after power on
|Automatic reset time after the failure
|Mean time to failure
||min. 10 000 000
||-10℃ ~ +70℃
||less than 95% not condensed
||Indoor/Outdoor (with rain-tent cover)
||relay dry contact signal; +12V level signal, pulse width >100ms, DC12V pulse signal
RS232/ RS485 electric standard, communications range ≤1200m. Available to connect with external CAN BUS and Ethernet
The brush-less anti-collision swing barrier is an intelligent passage management equipment developed
and produced by our company. It integrates the exquisite mechanical transmission, microprocessor
control, voice and various reading and writing technologies. By configuring different reading and
writing equipment, the intelligent control and management of the passage can be completed. The
machine can realize the public channel's dissuade and access control